Design criteria for self-lubricating plastic components intended to work without external lubrication.
Eliminate grease and oil? How to design a plastic component for dry running
Every few weeks, a guide must be re-lubricated. Grease traps dust. Oil migrates to an area that should remain clean. Or the component is practically inaccessible after assembly, making maintenance expensive or unfeasible.
In these cases, the design problem is not simply reducing the coefficient of friction. The question is more demanding: is it possible to eliminate external lubrication while maintaining durability, movement stability, and reliability throughout the required service life?
| Dry running does not simply mean “removing the grease” Switching from a lubricated system to a dry one changes the thermal balance, interface conditions, start-up behavior, and the way wear and contaminants are managed. |
Why lubrication can become a design constraint
Greases and oils are very effective tools for separating surfaces, reducing direct contact, and controlling friction. Their real cost, however, goes beyond the price of the lubricant. In addition to the initial application, re-lubrication, maintenance access, cleaning procedures, and checks on compatibility with materials and the environment may be necessary.
In some applications, the presence of a lubricant can also promote the adhesion of dust and particles, create migration issues, or be undesirable in areas that must remain clean. For this reason, a dry-running system can generate value not only by reducing maintenance but also by simplifying the design and stabilizing certain operating conditions.
Five questions to ask before designing for dry running
1. What is the actual combination of pressure and velocity?
Load and velocity influence the amount of energy dissipated at the interface. A lightly loaded bushing and a fast-rotating component require different approaches, even when the starting material is the same.
2. Is the motion continuous, oscillating, or intermittent?
Start-up, stop, and reversal phases can be more critical than steady-state operation. In short, repeated movements, the system may never reach a stable tribological condition; in continuous movements, however, heating and dissipation become central.
3. How is heat managed?
Eliminating a lubricant film also means changing the way the contact dissipates energy. In polymers, local temperature can markedly affect stiffness, creep, and wear. For this reason, it is useful to measure, whenever possible, the temperature near the contact zone and not just the ambient temperature.
4. What is the counterpart?
Material, hardness, treatment, and roughness of the opposing surface can lead to significant differences. The behavior of a compound against steel cannot be automatically associated with contact against aluminum, rubber, or another polymer.
5. What does “maintenance-free” really mean?
A requirement such as “no maintenance” must be converted into a verifiable goal: how many cycles, hours, or years must the component complete? What variation in torque, clearance, noise, or wear is acceptable before end-of-life?
How a self-lubricating compound works
In self-lubricating materials, the tribological function is integrated into the compound. Additives with different mechanisms can reduce adhesion, promote sliding, improve wear resistance, or increase the system’s operating margin.
However, there is no single additive suitable for every application. MoS2, graphite, aramid fibers, carbon fibers, silicone, PTFE, and PFAS-free alternatives act differently and introduce different trade-offs. The choice must therefore start from the load, velocity, and temperature profile and then include all secondary requirements.
Where dry running can create the most value
Automation and robotics
In high-cycle systems, reducing the need for re-lubrication can decrease interventions and simplify the management of hard-to-reach points. Guides, bushings, cams, joints, and small mechanisms are typical examples to evaluate.
Industrial machinery
A self-lubricating component can help reduce dependence on periodic maintenance and limit dirt buildup in moving areas, especially when the lubricant tends to trap particles present in the environment.
Electrical and electronic
In these applications, the migration of certain lubricants may be incompatible with contacts, surfaces, or aesthetic requirements. The formulation must therefore also be evaluated for surface stability, electrical properties, and process compatibility.
Food and pharma
The absence of grease can contribute to a cleaner environment and reduce certain contamination risks, but it does not automatically make a material suitable for food or pharmaceutical contact. The specific formulation must be verified against the intended regulations and application.
A practical path to converting a component to dry running
- Measure the current system: temperature, torque or force, wear, noise, maintenance frequency, and failure modes.
- Define the target life and end-of-life criteria.
- Collect pressure, velocity, temperature, type of motion, counterpart, roughness, and environmental conditions.
- Define non-tribological requirements: stiffness, creep, dimensional stability, chemical resistance, electrical properties, flame resistance, or specific compliances.
- Select multiple candidate materials and compare them under consistent conditions.
- Validate the material on the actual component and under the intended conditions of use.
When it is not advisable to eliminate the lubricant immediately
Dry running should not become an ideological goal. If the lubricant also performs a protective or sealing function, if the loads are particularly severe, or if the required life has not been reproduced in testing, eliminating it completely can increase risk.
In some projects, the most robust solution may be a reduction in lubrication, a longer maintenance interval, or a different contact architecture. The correct criterion remains system performance, not the mere fact that the material is defined as self-lubricating.
Material selection should reduce one variable, not create three new ones
The choice of a compound for dry running is effective when it integrates tribology, mechanics, thermal properties, and processing. The LATILUB family allows working on different matrices and self-lubricating systems, so as to adapt the balance of properties to the application instead of forcing a single solution.
Do you want to understand if your component can work without grease or oil?
| Fill out the LATI Tribology Design Check with motion, load, velocity, temperature, counterpart, current lubrication, required life, and the reason why you want to eliminate it. These data allow for building an initial shortlist of materials and defining which tests are truly useful. Discover LATILUB self-lubricating plastic materials |
